2024 Utility Trailer Flatbeds 4000AE®
- Year 2024
- Make Utility Trailer
- Model Flatbeds
2024 Utility Trailer Flatbeds 4000AE®
2024 Utility Trailer Flatbeds 4000AE®
ONE STEP AHEADOur flatbeds give you the assets that improve profitability
UNQUESTIONED
INNOVATION OF A HIGHER CALIBER
It flat-out betters the bottom line
Features may include:
Light weight, high strength, low maintenance- The 4000AE delivers the strength and durability of an all-steel trailer and the low weight benefit of an all-aluminum trailer.
- Designed with 3" aluminum crossbars, that include nine 4" full-width, tapered aluminum crossbars on 8" centerlines to provide optimized strength at the coil.
- Attached to the extruded aluminum floor, the 80,000 psi high strength steel hat-shaped top flange provides additional lateral stability to the trailer.
- The main beams are shot blasted to bare metal prior to painting and then coated with a two-part primer and two-part urethane top coat on the exterior surfaces. A rust preventative coating is applied to the interior surfaces of the beams for lower maintenance cost.
- Our patented crossmembers system is featured on the 4000AE. A combination of 3" and 4" aluminum crossmembers replace steel to optimize weight without compromising strength or functionality.
- Three tube-shaped outriggers located on each side of the flatbed are connected to the aluminum crossmembers, providing stability and helping distribute the load to the main beams.
Weights
GVWR
73,000 lb
Capacities
Payload Capacity
80,000 lb evenly distributed mainbeam
Dimensions
Dimensions
Kingpin location: 30" from front | Rubber dock bumpers: (2) ½" proud mounted on rear rail
Overall Length
48' 0"
Overall Height
583⁄16" on 47" height 5th wheel
Overall Width
102"
Depth, Maximum
Front gooseneck: 113⁄16"
Features
Features
Deck type: Straight | Kingpin plate: Integral with approach plate | Kingpin type: AAR hardness cruciform | Run up members: 4 steel angles run up members | Support legs: Jost® model A400 square 2-speed steel crank type | Support leg location: 140" from leading edge of front rail to center line of support legs | Support leg shoe type: 10" × 10" hinged square low profile sand support leg shoes | Support leg crank location: Roadside of support legs | Floor type: 1⅛" extruded aluminum flat top floor with hardwood nail strips at each side rails (2) | Floor joint sealant: Caulking applied prior to assembly between aluminum planks and wood nailers | Front wall lining: ¼" exterior grade plywood | Conspicuity tape location: On rub rail | Frame finish: Utility black enamel with primer undercoat on all steel show surfaces; aluminum parts receive a natural finish | Vertical & horizontal I.C.C. bumper finish: Utility black enamel on horizontal bumper, black scharpf on vertical bumper | Bottom side rail finish: Natural aluminum | Top front & top side rail finish: Extruded aluminum | Support leg finish: Rust preventative coating | Mudflap type: Black plastic anti-sail with Utility logo, mounted with steel reinforcing straps | Support leg bracing: Aluminum tube bracing | Slack adjusters: Bendix® Versajust® automatic | Axle manufacturer: Hendrickson® N-spindle type | Hub piloted system with outboard drums: Accuride® Trident 10 stud hub-piloted system with outboard balanced steel light weight drums with 16-1/2" × 7" brakes (standard with ConMet Preset Plus®) | Light weight hubs: ConMet aluminum | Hubcaps: Federal-Mogul “non-vented”
Construction Material
Vertical and horizontal I.C.C. bumper: “Wheels back” bumper with non-slip 7" deep horizontal | Front panels: .050" pre-painted white aluminum | Front wall posts: 2" extruded aluminum Zee | Front corner post: 7 ga. formed steel | Outriggers: 3 aluminum tube outriggers each side | Pipe spools: Extruded aluminum on 24" center line centered between pockets | Bottom flange: ½" × 4" high strength steel 80,000 psi
Chassis
Mainframe
Approach plate: ¼" steel, 45" wide, front 9" tapered up 3" | Frame web: 25¼" deep 7 ga. steel 60,000 psi one-piece | Hendrickson air ride system with integral axles: Hendrickson® AANT 23K INTRAAX air ride with LDA axles and 121" axle spacing
Chassis
Axle spindle nuts: ConMet® included with Preset Plus® | Coil reinforcing: Reinforcing for single 47,000 lb coil operation with 3 pairs of outriggers | Coil package reinforcement: 4" tapered end aluminum crossmembers in coil reinforcing area | Side pockets: ¼" extruded aluminum outside-type pockets on 24" center line | Crossmembers: 3" aluminum I-beam crossmembers on 16" center line full length; (9) 4" tapered aluminum crossbars on 8" center lines | Front rail: Aluminum with stainless steel front corners
Suspension
Suspension
Fixed air ride suspension location: 90½" center line to rear 121" spread
Brakes
Brake System Type
Air actuation system: 1 tank with spring brakes | Air brake chambers: Bendix® EnduraSure™ 3030 | Anti-lock brake system (ABS): Bendix® TABS-6 2S/1M | Brake lining style: Hendrickson® HXS brake lining style
Wheels & Tires
Wheels
Wheel bearings: ConMet® included with Preset Plus® | 22.5" × 8.25" standard width wheels: Factory choice steel 10 hub piloted wheels | Wheel bearing lubrication: Mobilube HD Plus 80W-90 oil
Tires, Rear Specification
Michelin® 275/80R 22.5 XTE 14 ply, load range G | Oil seals:Curtain tensioner assembly: V-shaped furling spool mounted above a ratchet base and lock at front
Electric
Electrical
Electrical receptacle: 7-way without circuit breakers | Main harness: Utility moisture-resistant 6-wire harness with internal ground and 7-way plug
Lights and Safety
Lighting
Stop, tail, turn lights: Grote® 4" LED (10-diode) lights, 2 per side with black snap-in flange | Clearance lights quantity: 1 top front corner diagonal (each side), 1 center of trailer (each side), 1 rear corner gusset (each side), 3 at rear | Lower clearance lights: 2½" round Grote® Ultra Seal 10 type | ABS warning light: Grote® Micronova® LED PC-rated